Roland - 支援 - SYSTEM-1 - 更新&驅動程式 - SYSTEM-1 System Update Ver.1.20

SYSTEM-1 System Update Ver.1.20

This is the latest version of operating system for the SYSTEM-1.

How to tell the version

Please check the version of the system working on your SYSTEM-1 before downloading the archive file.

Hold down [ KEY HOLD ] button and [ MOD ] button, and switch on the power.
SCATTER TYPE "1" and the [ ARPEGGIO ] button flash.
Press the [ ARPEGGIO ] button.
If the panel display for SYSTEM-1 is other than as described below, carry out the update.
- The Memory [ 2 ] button are illuminated.
After checking version of the product, power off the SYSTEM-1 without performing any button operation.

Update history

For details, refer to "SYSTEM-1 Update leaflet (Ver.1.20)" ( SYSTEM-1_v120_e01_W.pdf ) and "SYSTEM-1 Version 1.20 Operation Guide" ( SYSTEM-1_v120_guide_e01_W.pdf ) in the [ Owner's Manual ].

What you will need to update your SYSTEM-1

SYSTEM-1
AC adaptor
USB cable
A computer with a USB connector ( Windows 8 / 7 / Vista, MacOS X )

Caution when performing the update

Never apply this update data to any product other than the SYSTEM-1. This update data may destroy the data or system program of other products.
Never power-off your SYSTEM-1 while the update is in progress!
If a power failure or similar accident occurs during the update process, the SYSTEM-1 won’t be able to start up in normal operating mode. This will require servicing, so you will need to contact Roland service center near you if this occurs.
We regret that we are unable to answer questions regarding the update procedure using this system program. Please perform the update responsibly, following the directions given in this document.

Getting the update file

Please open/extract the downloaded "sys1_sys_v120.zip" file on your computer to get the update file in the "sys1_sys_v120" folder.

IMPORTANT : Data Backup / Restore
Updating to version 1.20 initializes all data saved in the SYSTEM-1's patch memory.
To keep existing created data, follow the procedure in "Backup" to back up the data before carrying out the update.
After updating, you can restore the original content of the patch memory by following the procedure in "Restore" to restore the data.

Backup

Hold down [ ARPEGGIO ] and switch on the power.
Connect your computer to the SYSTEM-1's USB port via USB cable.
Open the "SYSTEM-1" drive folder on your computer.
Copy the SYSTEM-1 Memory files in "BACKUP" folder into your computer.

SYSTEM-1 : SYSTEM1_PATCH1.PRM - SYSTEM1_PATCH8.PRM
PLUGOUT : PLUGOUT_PATCH1.PRM - PLUGOUT_PATCH8.PRM
* PLUGOUT_xxx.PRM files are displayed only when the SYSTEM-1 used as a plug-out synthesizer.
After copying is completed, disconnect the USB cable.
With Windows 8 / 7 / Vista

Right-click on the "SYSTEM-1" icon in My Computer and execute "Eject."
With Mac OS

Drag the "SYSTEM-1" icon to the Trush icon in the Dock.
Turn the SYSTEM-1 power off.

Restore

Hold down [ ARPEGGIO ] and switch on the power.
Connect your computer to the SYSTEM-1's USB port via USB cable.
Open the "SYSTEM-1" drive folder on your computer.
Copy the SYSTEM-1 memory files into the "RESTORE" folder.
After copying is completed, disconnect the USB cable.
With Windows 8 / 7 / Vista

Right-click on the "SYSTEM-1" icon in My Computer and execute "Eject."
With Mac OS

Drag the "SYSTEM-1" icon to the Trush icon in the Dock.
After the OCTAVE [ DOWN ] [ UP ] buttons have completely stopped blinking, turn off the power.

Procedure for the update
Caution

You must not rename the extracted file.
Never turn off the SYSTEM-1's power while the update is in progress. Otherwise the system program or the SYSTEM-1 itself may be destroyed.

Please install the extracted system program file into your SYSTEM-1 according to the following procedure.

Hold down [ KEY HOLD ] button and switch on the power.
All four buttons from [ KEY HOLD ] to [ MOD ] flash.
Connect the computer to the SYSTEM-1's USB port by a USB cable.
Only the [ KEY HOLD ] button flashes.
Open the "SYSTEM-1" drive folder in your personal computer.
Copy SYSTEM1_UPD.BIN in the "sys1_sys_v120" folder into the "SYSTEM-1" drive by dragging and dropping it.
* Do not copy the "sys1_sys_v120" folder.
After copying the file is completed, remove the USB drive from the personal computer.
With Windows 8 / 7 / Vista

Right-click on the "SYSTEM-1" icon in My Computer and execute "Eject."
With Mac OS

Drag the "SYSTEM-1" icon to the Trush icon in the Dock.
Disconnect the USB cable.
The [ DOWN ] button lights.
Press the [ DOWN ] button to start updating the file.
After updating processing is completed, all the four buttons on the display ( between the [ KEY HOLD ] and [ MOD ] buttons ) blink.
Turn the SYSTEM-1 power off.
Please verify the version number with the procedure described in "How to tell the version" part of this document.
When the update has finished, follow the procedure below to execute a factory reset.
1. Hold down [ MANUAL ] button and switch on the power.
  [ ARPEGGIO ] button flashes.
2. To execute the factory reset, press [ ARPEGGIO ] button.
  When all buttons light up, the factory reset has finished.

Roland Software License Agreement

In no event shall Roland Corporation be liable to end-users for any damages whatsoever, including but not limited to financial damages for any loss of profits or information arising from the use of, or inability to use this updater. The foregoing provision is effective even if Roland Corporation has been advised of the possibility of such damages.

This is a legal agreement between you (an individual or a corporation) and Roland Corporation (herein referred to as "Roland") regarding the usage of this software product (herein referred to as "SOFTWARE"). Please read carefully the terms of this License Agreement before installing or using the SOFTWARE. By installing, copying, or starting the use of the SOFTWARE, you hereby consent to the terms of this License Agreement.

1. GRANT OF LICENSE

Roland grants you the following non-exclusive rights to use the SOFTWARE in accordance with the terms of this License Agreement.
(a) You may only use the SOFTWARE on a specific single computer at one time. Use of the SOFTWARE shall include loading the SOFTWARE into temporary memory (i.e., RAM) or installing the SOFTWARE into storage media (i.e., hard disk) of the computer on which you will use the SOFTWARE.
(b) You may make one copy of the SOFTWARE for backup purposes only (on floppy disk, magneto optical disk, DAT or the similar media), but you are prohibited to make any other copy.

2. COPYRIGHT

The SOFTWARE and its copyrights are the property of Roland and are protected by all international copyright laws and treaties.
Therefore, you must treat the SOFTWARE like any other copyrighted material (i.e., a book or a CD). All rights that are not provided for herein are reserved by Roland.

3. OTHER RESTRICTIONS

(a) You shall not modify, change, reverse engineer, decompile, or disassemble the SOFTWARE and the copyright notice and copyrighted logo.
Unauthorized copying, uploading to another network, distributing, modifying and/or attaching this software to other media or any other sales item is expressly forbidden.
(b) You shall not loan, rent, lease, sublicense or transfer the SOFTWARE, either in whole or in part, to any third party. But you may permanently transfer the SOFTWARE and accompanying printed materials provided you retain no copies of the Software and recipient agrees to the terms of this License Agreement. If the SOFTWARE has been updated or upgraded, any transfer of the SOFTWARE must include the most recent update and all prior versions.
(c) If this SOFTWARE contains multiple templates of media (such as floppy disks and CD-ROM) and these media contain the same software, you may use only the one form of media that is appropriate for your computer. You shall not use the remaining form(s) of media on another computer.
(d) You may not use the Software from multiple locations of a multi-user or networked system at any time.

3.2 Open source software and other third party software
(a) The SOFTWARE may use open source software and other third party software (herein referred to as "OSS, etc.").
(b) The OSS, etc. in the case of the preceding paragraph shall be subject to the OSS, etc. license (herein referred to as "OSS License"), and you shall comply with the OSS License.
(c) If there are any differences between the terms of this License Agreement and the OSS License, the OSS License shall prevail and the terms of this License Agreement shall not apply.

4. NO WARRANTY

Roland makes no warranty, either expressed or implied, with respect to any of the software, including, without limitation, any implied warranties of merchantability or fitness for a particular purpose.

5. NO LIABILITY

Roland can not reply to inquiries regarding this system software updater. Please read the instructions completely, and please note that you should use the SOFTWARE AT YOUR OWN RISK.
In no event shall Roland be liable to end-users for any damages whatsoever, including but not limited to financial damages for any loss of profits or information arising from the use of, or inability to use this product. The foregoing provision is effective even if Roland has been advised of the possibility of such damages. Even if the SOFTWARE has any material, verifiable, and reproducible program errors, Roland shall have no liability to modify such errors.

6. TERMINATION OF THE LICENSE

Roland reserves the right to terminate this License Agreement if you fail to comply with any of the terms of this License Agreement. Upon such termination, you shall immediately stop using the SOFTWARE.

7. GENERAL

(a) Any provision of this Agreement which is prohibited or unenforceable in any jurisdiction shall be ineffective to the extent of such prohibition or unenforceability without affecting, impairing or invalidating the remaining provisions hereof.
(b) This License Agreement shall be governed by and construed in accordance with the laws of State of California without reference to the principles of conflicts of laws.

SYSTEM-1 System Update Ver.1.20

支援

Quick Links